Based on real-world events. To protect confidentiality, the names of companies, products, people, and places, along with any proprietary or confidential details, have been changed or removed. Some details have been combined or simplified for teaching, and any data shown are illustrative. Any resemblance to a specific company, product, or person is coincidental.
At a glance
| Product / test | SDS-PAGE identity and degradation test for a therapeutic protein, quantified by densitometry |
|---|---|
| Specification | Degradation < 5% |
| The problem | Two lots read 6–9% degradation, although the gel looked normal by eye |
| Root cause | A deteriorated degraded standard ran lighter than normal. Because the method sets scan sensitivity for the whole gel against that standard, every sample lane was magnified. |
| Why it wasn’t caught | The standard’s preparation date wasn’t recorded, so its 30-day expiry couldn’t be verified or enforced |
| How it was proven | Retest of the same samples under a pre-approved protocol, with the old and a new standard side by side |
| Outcome | Assignable cause documented; OOS invalidated with QA approval; lots released; SOP revised; CAPA effective |
How the test works
Each gel has ten lanes: a molecular-weight (MW) standard, a positive control, a negative control, a blank, and two sample lots in triplicate. A degraded standard, a protein sample with a known amount of breakdown, serves as the system suitability check.
After staining, the gel is scanned on a calibrated densitometer. Per the validated SOP, the analyst raises the scan sensitivity for the whole gel until the degraded standard shows at least 5% degradation, but stops before the negative control shows any. Software then calculates degradation in each sample lane. The key point: the sensitivity setting applies to every lane at once.
1. The signal
On a routine release gel, both sample lots read between 6.1% and 8.8% degradation across their triplicate lanes: out of specification. Yet when the analyst and reviewer looked at the gel itself, the sample lanes looked like every passing gel before them: a strong main band and only faint minor bands.
2. Contain and define
- Contain. Both lots placed on hold; QA notified the same day under the OOS procedure.
- Preserve evidence. The gel image, the scan file with its settings, retained sample portions, and the degraded standard vial in use were kept and labeled.
- Define. The team wrote a problem statement and an Is / Is-Not.
| Is | Is not | What it suggests | |
|---|---|---|---|
| What | High degradation by software (6–9%) | Visible extra degradation by eye | The number, not the protein, may be the problem |
| Where | All six sample lanes, both lots | One lane or one lot only | Something acting on the whole gel |
| Which control | Degraded standard lighter than normal | MW standard, positive and negative controls, blank | The standard is the odd one out |
| When | This gel | Previous gels (normal results) | Something changed recently |
3. Was the run valid?
The first question in any OOS is whether the test itself worked. The MW standard separated normally, the positive control showed its expected band, and the negative control and blank were clean. The degraded standard met the SOP’s suitability window: it reached 5% before the negative control showed any degradation.
So the run was technically valid under the SOP, and the OOS results couldn’t simply be set aside. The investigation had to find a cause.
4. Finding the mechanism
The software record showed the scan sensitivity used for this gel was 78, compared with a typical range of 40–55 on recent passing gels. Because the degraded standard was light, the analyst had to raise sensitivity much further than usual to make it show 5%.
That explained everything at once. Higher sensitivity magnifies faint signal in every lane. The negative control, with nothing to detect, stayed at 0%. But the samples’ small, normal minor bands and background were magnified into 6–9% “degradation.”
Working hypothesis
A weak degraded standard forced an unusually high gel-wide sensitivity setting, which inflated the degradation results for normal samples.
5. Phase I laboratory investigation
Reagents and gel-wide factors
Stain, destain, buffers, and the gel itself were early suspects. But these act on the whole gel, and every other lane looked normal. Only the degraded standard lane was light, which pointed to a lane-specific cause: the standard itself, its preparation, or its loading.
Records and SOP review
- Analyst interview: preparation, loading, and staining followed the SOP; nothing unusual noticed except the faint standard.
- Densitometer: within calibration.
- SOP: the degraded standard is stored frozen between uses and is good for 30 days.
- Gap found: the standard’s preparation date was not recorded anywhere, so its age, and whether it was within its 30-day expiry, couldn’t be determined. The vial had been thawed and refrozen for each use, with no limit on freeze-thaw cycles.
6. Proving the cause
QA approved a written protocol before any retesting. It stated the hypothesis (a weak degraded standard inflated the results), specified a retest of the same retained samples, and put the old standard and a freshly prepared standard on the same gel. Sensitivity was set per the SOP using the new standard.
| Lane | Result | What it shows |
|---|---|---|
| New degraded standard | Normal intensity; reached 5% at sensitivity 46 | Sensitivity back in the typical range |
| Old degraded standard | Visibly lighter; read only 2.7% at the same setting | The old standard had lost signal |
| Lot 1 (triplicate) | 1.9%, 2.1%, 2.3% | Passes; consistent with history |
| Lot 2 (triplicate) | 2.0%, 2.2%, 2.4% | Passes; consistent with history |
| MW standard, controls, blank | Normal | Valid run |
With a normal standard, sensitivity returned to its usual range and both lots passed. Running the old standard on the same gel showed directly that it had weakened. That side-by-side comparison turned a likely explanation into a demonstrated cause.
Supporting check (why it weakened): fresh standard aliquots put through repeated freeze-thaw cycles lost visible intensity after several cycles, consistent with the old vial’s thaw-and-refreeze history.
7. Method or input?
The method lets the standard set the scale for the whole gel, so a weak standard can inflate every result. The team considered redesigning the method but decided against it. SDS-PAGE with densitometry is semi-quantitative by nature, the bracketing approach is common practice, and the method was validated. Revalidation would be costly and wouldn’t remove the reliance on a good standard.
Instead, the team chose to control the input: make sure the degraded standard is always within its expiry and in good condition, and make unusual sensitivity settings visible.
8. Root cause statement
| Trigger | The degraded standard had deteriorated (lost signal) after repeated freeze-thaw cycles over an untracked period of use. |
|---|---|
| Mechanism | Because sensitivity is set for the whole gel against the standard, the analyst raised it well above normal, magnifying faint signal in every sample lane. |
| Why it wasn’t prevented or detected | The standard’s preparation date wasn’t recorded, so the 30-day expiry couldn’t be enforced. There was no freeze-thaw limit, and no check on how high the sensitivity setting had to go. |
9. Disposition of the OOS results
- QA approved invalidation of the original OOS results, with the protocol, gel images, and sensitivity records attached as the assignable cause.
- Both lots were released on the passing retest results.
- Look-back: other gels run with the old standard were reviewed. A weak standard pushes results higher, never lower, so earlier passing results couldn’t have hidden a failure. No other lots were affected.
10. CAPA
| Type | Action |
|---|---|
| Correction | Old degraded standard discarded; fresh standard prepared. |
| Corrective action | SOP revised: the degraded standard’s preparation date is recorded on the results form, so the reviewer can confirm it is within its 30-day expiry. |
| Corrective action | Standard vials labeled with preparation date, expiry, and preparer. |
| Preventive action | Standard prepared as single-use aliquots, so no vial is thawed and refrozen. |
| Preventive action | The sensitivity setting is recorded for every gel, with a typical range. A setting outside that range triggers a check of the standard before results are approved. |
| Training | Analysts and reviewers trained on the revised SOP and on why a weak standard can inflate results. |
11. Effectiveness check
Criteria were set before closing: over the next 30 days (one full standard life cycle) and at least 10 gels, no OOS results linked to the standard, the standard’s preparation date recorded on 100% of results forms, and every sensitivity setting within the typical range. All criteria were met, and the CAPA was closed as effective.
12. The tools at a glance
| Stage | Tool | Pros | Cons |
|---|---|---|---|
| First look | Visual review vs. software | Fast; exposed the contradiction | Subjective |
| Define | Is / Is-Not | Showed a gel-wide effect with one odd control | Doesn’t prove cause |
| Run validity | System suitability review | Settled whether the OOS stood | Window criteria can pass with a weak standard |
| Mechanism | Method logic + audit trail | Explained every observation | Needs experimental confirmation |
| Narrow | Is / Is-Not on the lane pattern | Ruled out reagents instantly | Narrows, doesn’t prove |
| Why weak? | Records and SOP review | Found the untracked expiry | Records couldn’t answer the question |
| Confirm | Pre-approved retest, paired comparison | Demonstrated the cause in one run | Relies on well-stored retained samples |
| Decide | Risk-based judgment | Proportionate fix, no revalidation | Method dependence remains |
| System cause | 5 Whys | Reached fixable system gaps | Only reliable after the cause is proven |
Key takeaways
- When the picture and the number disagree, investigate the number. Normal-looking lanes were the first sign the problem was in the measurement.
- Know how your method scales. When one reference sets the sensitivity for the whole gel, a weak reference distorts every result.
- Let the lane pattern guide you. Gel-wide causes can’t explain a single weak lane.
- An expiry you can’t verify isn’t a control. Recording the preparation date turned a rule into something reviewers can check.
- Put the suspect next to a known-good version. The side-by-side standards made the cause visible.
- Fix what matters in proportion. Controlling the standard solved the problem without revalidating the method.
- Know which way the bias runs. A weak standard only inflates results, which kept the look-back simple.
Questions to think about
- The run passed system suitability. Why couldn’t the OOS results be invalidated on that basis alone?
- Why is re-analyzing the original scan at a lower sensitivity not an acceptable fix?
- What made running the old and new standards on the same gel so much stronger than using only the new one?
- Which reagents or standards in your lab have expiries that aren’t actually tracked?
- When would it be worth redesigning or revalidating the method instead of controlling the standard?
Related reading: The Oven That Only Failed Sometimes and Advanced Root Cause Analysis.
Kepner-Tregoe is a proprietary method of its owner, described here for educational purposes only. QStead Group is not affiliated with it. This case study is for educational purposes only.
Working through an OOS or CAPA investigation that won’t close? Get in touch.